The knowledge Support BiloSatCCam
- Dreambox HD Flashing firmware by Browser
- How to flash on web interface (<5 minutes)
- reset your dreambox password using REMOTE CONTROL
- Quick install new image & old settings in Dreambox
- How to add more servers to your Addons
- How to E2 images Add / Remove Packages or Plugins
- Basic CCcam lines
- Dreambox Image Install With FlashWizard Program
2- Vu+- How to flashing your VU+ Duo With A USB Stick
- How to Flashing Your VU Solo BY USB
- Dummies guide to setting up Vu+Duo
- 3- AzBox
- HAzbox Emergency Flash
- How to Update firmware on azbox
- How to flash AzBox Me with Enigma 2 over Web interface
- For CCcam 2.2.1in E2 for AZbox HD
- How to use Mgcamd with CCcam and Newcs
- Azbox CCcam Tutorial > client & server
4- OPENBOX- How To Load CCcam.cfg Card Sharing Into Skybox/Openbox HD Satellite Decoder Using Thumbdrive
- How To Load Or Setup CCcam Card Sharing On Skybox/Openbox S9 Using Remote Control
- How to upgrade OpenBox S10 HD PVR Firmware
5- SPIDERBOX-
6- QBOX-
HOW TO: Dreambox HD Flashing firmware by Browser
What you need to flash
You need the image file you want to flash. Image files have the extension *.nfi. You can’t flash other
images like *.img files. Don’t try it – it won’t work.
You need either a DHCP server and a configured bootloader
You need a browser and a network cable. Connect your Dreambox to a switch/hub/router in your lokal LAN.
To flash a new image, you can use the second stage loader. It must be present and not broken.
The following steps assume you have a DHCP server.
If you don’t have one, you have to setup an IP address (klick) in the bootloader’s serial setup.
- Power down the Dreambox, either using “shutdown” and by switching off by the power switch.
Standby is not enough!
- (1.) Press and hold the power button.
- (2.) Switch on your Dreambox.
- (3.) Your Dreambox will get the next free DHCP IP address from your router
- Now, open a browser on your PC.
(1.) enter in the address line “ip/” .
- (2.) on the bottom of the page, there’s a link called “firmware upgrade”. Click it.
- On the next page, you can select the flash image you want to flash. be sure that it has the “.nfi” extension.
You can’t flash other images (like .img)!
- Click on “FLASH!” and wait. It might take some time to upload and flash the image.
- Switch the box off again, and on again. The new image should be flashed and working
How to flash on web interface (<5 minutes)
This tutorial was realized with DM800 guenuine part (original) it’s probably OK with clones…
1) Unplug 12V power source.
2) Push start button & plug 12V power source
3) Your dreambox start to boot & stop (you can see your IP adress to access web interface)
4) Just insert this IP adress on your browser’s adress bar & run…
Download pictures in attached-
-
HOW TO : reset your dreambox password using REMOTE CONTROL
You can reset your dreambox password using dreambox remote:
1.install tuxbox commander using addons button
2. Start tuxboxcomander
3.go to in /var/etc/ and open the file passwd
4.press 4 on remote to go into edit mode.
The first line is root:*****:0:0:root:/home/root:/bin/sh
where the ****** delete it (by using remote arrows to move cursor right and then pressing volume minus)
delete *** until upto :0:0:rootand press ok and exit -> save
the first line should look like this after the edit
root::0:0:root:/home/root:/bin/shthen login with user root and password leave empty
you could telnet and change the empty password with your own so known can easily hack into your dm box
-
HOW TO : quick install new image & old settings in Dreambox.
You need:
Total Commander or other client FTP
DCC – Dreambox Control Center
Flash Wizard – or other program for Flash new image.1) Back-up.
First will have to copy all programs installed and settings from DM.
From FTP will copy in hdd what we have installed in/from DM:
/var/bin – attention do not copy enigmanet ! Copy only CAM and SCRIPT installed !
/var/etc
-movieplayer_linux.xml – if exist.
-movieplayer_win.xml – if exist.
-satellites.xml – actual list with satellites and transponders. Optional./var/keys – copy all.
/var/script – copy script for launch CAM and installed programs ! check in Blue Panel to see what CAM you have and check Plugins ( Tools ) to see installed programs.
/var/tuxbox/config
/var/tuxbox/plugins
- copy all.
- attention do not copy link to another directory, like link to scce !/var/uninstall – copy all.
For safety write down your DM password and settings from Communication Setup.
For safety make a backup copy of your image and settings with Flash Wizard.
2) Install new image.
Install new image ( Flash Wizard ) and restart DM, unplug DM from AC, wait few second and plug again.
If image it is correct programmed DM will start and settings menu will appear.
Do not set anything.3) Reinstall your settings and programs.
From telnet change your password in DM with old one.
From FTP copy saved settings and programs in the same place.
/var/bin
/var/etc – optional
/var/keys
/var/script
/var/tuxbox/config
/var/tuxbox/plugins
/var/uninstallRestore attribute 755 at files from:
/var/bin – all
/var/script -*.sh
/var/tuxbox/plugins *.so
/var/uninstall *.sh4) Final.
It is very important do not restart/reboot DM from menu/telnet/sw because DM will save his setting over your restored ones.
unplug DM from AC, wait few second and plug again.DM will restart with new image and ALL settings as before.
Tips
* check how much space you have free in your old image, it is possible that in new image will not be the same free space for you to install all your stuff.
If you don’t have enough free space do not try to reinstall from first try all the plugins.
However it is important to reinstall complete dir. vartuxboxconfigenigma
* check settings in Communication; if you use DHCP and DM have all the time the same IP in the network is no problem;
Other way remember that after you reprogram DM will have new default IP and password -
HOW TO : add more servers to your Addons
-
Basic CCcam lines
-
How To: Dreambox Image Install With FlashWizard Program
Dreambox Image Install With FlashWizard Program
Dreambox Image Install With FlashWizard Pro
1. Extract Flashwizard Pro to a folder of your Choice.
2. Start Flashwizard with the FlashwizardPro.exe.
3. Click the configuration tab and select you language
4. On the same page you’ll need to fill in the Connection Parameters at the top of the page
5. If you have not changed you password Login= root password = dreambox.
6. To obtain your dreambox IP do the following on your dreambox remote.
Menu-Setup-Expert Setup-Communication Setup.
You’ll see your IP at the top of the page make a note of this and enter this IP into Flashwizard.
Also untick the DHCP box so your Dreambox IP will never change and remain static.
7. Now click the install a firmware tab top left
8. Now click on the yellow folder, this will open a browser window
Now navigate to the Dreambox image you would like to install.
11. You’ll now see the image been transfered
12. And then image transfer completed.
20. Now select Auto Transponder Scan. This will scan all available transponders till a valid one is found. When found press green to scan. When the scan is complete press ok.At this point you can now scan another satellite with a press of the green button or red not to. Later on in this tutorial ill be explaining how to transfer channel setting so you don’t really need to.
13. Exit Flashwizard and pull the power from you dreambox and wait for 30 seconds before reapplying power.
14. Time to get sat in front of the TV! As your box boots you’ll see the Boot Logo Screen come up maybe a couple of times.
15. At the Pal Screen Select Pal or the system your TV uses and then press the green button on your remote to save.
16. Select your language and press the ok button.
17. Select your time zone and press the green button to save.
18. You’ll now see the Diseqc Setup menu and have 3 options to choose from
No Diseqc for a single LNB Setup.
Simple For a the setup of 2 Lnb’s
Complex for Diseqc 1.2 or Usuals/Goto X
19. If you want to use usuals keeps the goto x box ticked and enter your Longitude and latitude and press the green button to save.
21. Click exit and select a channel free to air to view.Now press the menu button-option5-reboot now, this will save your settings.
That’s the flash and initial setup complete
-
-
VU + Duo: HOW TO : flashing your VU+ Duo With A USB Stick
-
HOW TO : Dummies guide to setting up Vu+Duo
Dummies guide to setting up Vu+Duo
” These instructions are for Dream Elite Image, other images Green & Yellow buttons might be configured slightly different.
1. Install image.
Download a USB image file, eg Dream Elite from
Vu+ Duo Dream Elite Image Section
Unzip the vuplus folder to the root directory of a USB Pen Drive.
Power off Vu+ with switch on the back
Insert USB Pen Drive into the USB socket on Vu+
Power on Vu+
Image will auto install from the USB Stick.
Look at the display on the receiver, it’ll display when the update has finished.
Remove the USB Stick
Power off receiver.
Power on Receiver.
Image is now installed.
2. Network
Connect an Ethernet LAN cable from your router to your Vu+ Ethernet port.
Press Menu
Select Set Up
Select System
Select Network
Select Network w i z a r d and press OK.
3. Setup Motorised Dish using USALS
First get your longitude & latitude info from multimap.com
Enter your post code into multimap.com and you’ll get the correct LON & LAT info for your location.
Example if I enter the following UK postal code: SE1 6JZ
I get the following LON & LAT:
LON: 0.104 WEST
LAT: 51.497 NORTH
Press Menu
Select Setup
Select Service searching
Select Tuner configuration
Select Tuner A and press OK
Configuration Mode: Simple
Mode: Positioner
Longitude: input the info from multimap
Latitude: input the info from multimap
Press OK to save.
Press Menu
Select Setup
Select service searching
Select Positioner Setup
Select goto 0 Press RED Button
Dish should now go to 1w.
4. Download Channel List
Press Green Button
Press Yellow Button (Addons)
Select Addon Download Manager
Select Enigma2 Settings
Select Likra E2 Setting Motor and press OK.
5. Install cam
Press Green Button
Press Yellow Button (Addons)
Select Addons Download Manager Press OK
Select Image Cams Press OK
Select the cam you want to install and press OK
6. Activate cam
Press Blue button.
Use Left & Right Keys to select an installed cam and press OK.
This is enough to get you started, the fun starts learning the rest-
Azbox Emergency Flash
-
-
-